FPInnovations’ three-generation floor vibration-controlled design methods in NBCC and CSA O86 ensure market acceptance by consumers. Since 1990, there have been very few consumer complaints. This reinforces the use of wood as a quality building material and contributes to expanding market shares of wood construction in Canada.
Comme l'ont démontré le développement et la mise en oeuvre des codes des méthodes de conception de troisième génération pour lutter contre les vibrations des planchers, FPInnovations joue un rôle important au Canada et à l'échelle internationale dans les comités de codes et de normes visant à protéger les consommateurs et l'industrie du bois et contribue à la croissance continue du marché de la construction en bois à l'échelle mondiale.
FPInnovations a lancé un projet de
recherche pluriannuel pour mesurer les fréquences
naturelles et les taux d’amortissement des
bâtiments en bois de moyenne et grande hauteur
afin d’élargir la base de données et de valider ou
d’adapter les équations existantes pour estimer les
fréquences naturelles. Deux immeubles de grande
hauteur en bois équipés d'un anémomètre et
d'accéléromètres sont également surveillés en
permanence pour étudier comment le vent excite le
bâtiment.
In the construction of buildings, the timber-concrete (TCC) system can be a cost-competitive solution for floors with longer spans, since the mechanical properties of the two materials are used efficiently. Furthermore, the additional mass from the concrete improves the acoustic performance compared to a timber floor system alone. Nevertheless, TCC floors are not commonly used in buildings in Canada, due to the absence of technical guidelines for such types of structural systems in this country.
FPInnovations launched a multi-year research project to measure mid- to high-rise wood buildings’ natural frequencies and damping ratios to expand the database and validate or adapt the existing equations to estimate the natural frequencies. Two high-rise wood buildings equipped with an anemometer and accelerometers are also being constantly monitored to study how the wind excites the building.
Three performance attributes of a building for serviceability performance are 1) vibration of the whole building structure, 2) vibration of the floor system, typically in regards to motions in a localized area within the entire floor plate, and 3) sound insulation performance of the wall and floor assemblies. Serviceability performance of a building is important as it affects the comfort of its occupants and the functionality of sensitive equipment as well. Many physical factors influence these performances. Designers use various parameters to account for them in their designs and different criteria to manage these performances.
The overall objectives of this stud were threefold:
1. The vibration performance tests were to experimentally determine the dynamic properties, e.g., natural frequencies (periods) and damping ratios of the WIDC building through ambient vibration testing on:
o the bare structure in 2014,
o the finished building upon completion of the construction with occupants in 2015, and
o the finished building after 3 years of service in 2017.
2. The floor vibration tests were to evaluate vibration performance of the innovative CLT floor based on the bare floor fundamental natural frequency, 1 kN static deflection, and subjective evaluation.
3. The sound transmission tests were to determine the Apparent Sound Transmision Class (ASTC) and Apparent Impact Insulation Class (AIIC) of selected innovative CLT floor assemblies.
ASTM and ISO standard test methods were used for the floor vibration and sound insulation performance tests. The verified FPInnovations’ protocol was used for building vibration performance tests.
In-situ tests carried out on the Wood Innovation and Design Centre have provided solid data on the serviceability performances of taller mass timber buildings, for both before and after completion. These data could be referenced by architects and engineers to help them in their designs and modelling to control building vibrations, floor vibrations and sound insulation performance. More specifically, the floor vibration performance was found to be satisfactory, and the sound transmission ratings were found to be above the minimum required level specified by the building code.
As observed from the tests on sound insulation performance, it is recommended to avoid small cavities in floor or wall assemblies to improve and optimize the acoustical performance. Based on the feedbacks and our experience of building vibration performance, it also recommended to refine the design tool, such as the building dynamic analysis model, using the measured frequencies so to improve the accuracy of the estimated building frequencies.
Advanced wood-based solutions for mid-rise and high-rise construction: in-situ testing of the Origine 13-storey building for vibration and acoustic performances
Serviceability performance studied covers three different performance attributes of a building. These attributes are 1) vibration of the whole building structure, 2) vibration of the floor system, typically in regards to motions in a localized area within the entire floor plate, and 3) sound insulation performance of the wall and floor assemblies. Serviceability performance of a building is important as it affects the comfort of its occupants and the functionality of sensitive equipment as well. Many physical factors influence these performances. Designers use various parameters to account for them in their designs and different criteria to manage these performances. Lack of data, knowledge and experience of sound and vibration performance of tall wood buildings is one of the issues related to design and construction of tall wood buildings.
survey.
This report addresses serviceability issues of tall wood buildings focusing on vibration and sound insulation performance. The sound insulation and vibration performance may not affect building's safety, but affects occupants' comfort and proper operation of the buildings and the funciton of sensitive equipment, consequently the acceptance of midrise and tall wood buildings in market place. Lack of data, knowledge and experience of sound and vibration performance of tall wood buildings is one of the issues related to design and construction of tall wood buildings.
Advanced wood-based solutions for mid-rise and high-rise construction: in-situ testing of the Brock Commons 18-Storey building for vibration and acoustic performances
This report addresses serviceability issues of tall wood buildings focusing on their vibration and sound insulation performance. The sound insulation and vibration performance may not affect the building’s safety, but affects the occupants’ comfort and the proper operation of the buildings and the function of sensitive equipment, consequently the acceptance of the midrise and tall wood buildings in market place. Lack of data, knowledge and experience of sound and vibration performance of tall wood buildings is one of the issues related to design and construction of tall wood buildings.
The measured and estimated values should also be correlated with actual experiences of the occupants in the building if such information is obtained, for example, through a survey.
Lack of research and design information for the seismic performance of balloon-type CLT shear walls prevents CLT from being used as an acceptable solution to resist seismic loads in balloon-type mass-timber buildings. To quantify the performance of balloon-type CLT structures subjected to lateral loads and create the research background for future code implementation of balloon-type CLT systems in CSA O86 and NBCC, FPInnovations initiated a project to determine the behaviour of balloon-type CLT construction. A series of tests on balloon-type CLT walls and connections used in these walls were conducted. Analytical models were developed based on engineering principles and basic mechanics to predict the deflection and resistance of the balloon-type CLT shear walls. This report covers the work related to development of the analytical models and the tests on balloon-type CLT walls that the models were verified against.
